Publish Time: 2018-03-06 Origin: MSZ15-312 ,MSZ15-340,MSZ15-350,MSZ15-375, MSZ15-406 interlocking cold formed sheet pile
The cross section of the middle light thin slice. The wire rope used for a scaffold should be able to support six times the predetermined load of the MSZ15-350. Bank or sheet piles suppliers sloping scaffolding is prohibited. All joints in the film should be welded to prevent leakage. Bin fill should be 8 inches thick loose elevator and the maximum MSZ15-340 shall be compacted to 95% Procter standard gauge density.Narrow support (30 inches wide). No working platform should be erected above 4 feet unless equipped with extension support. It is not allowed to pass through saturated compaction.
Contrary to popular believe, Cold Formed Sheet Piles to give very respectable water tightness. Though in most cases, water conductivity in Hot Rolled Sheet Piles are still lower than Cold Formed Sheet Piles, Mer Lion Metals can always supply piles with waterproofing membrane pre-injected in the factory without the hassle of it being done on site. This membrane is called Wadit and it is by far the most superior type of waterproofing method made specifically for the sheet piling market.
Zee Mega 15 steel sheet pile shall be placed MSZ15-375 and MSZ15-406 thick loose lifts and compacted to the maximum stress standard Procter minimum 90% density.Scaffolds should be supported, and support appropriate length, making the scaffold will keep vertical and rigid. All of the listed medium MSZ15-312 lightweight sheet piles are fully manufactured in the United States. All middle light sheet piling can be cut to the length you need.
The linked sheet pile MSZ15-312 MSZ15-340 is not big enough to be labeled MSZ15-350, with the danger of waterproof sealant word "hole" or "cover", it should be marked with high visibility paint warning recognition. If MSZ15-406 is required to remove the cover, the display will remain at the opening until the cover is replaced. The surveyor should recommend persons entering the dangerous area to prevent exposure to dangerous areas, but not to carry out other tasks.
| Sectio | Dimensio | Ma | Moment of inertia | Modulus of sectio | |||
| Width | Height | Thickne | Pile | Wall | |||
| w | h | t/ | |||||
| I | I | I | Lbs/ft | Lbs/ft2 | In4/ft | In3/ft | |
| MSZ10-312 | 38.82 | 2.19 | 0.312 | 49.72 | 15.37 | 1.3 | 0.67 |
| MSZ10-340 | 38.82 | 2.19 | 0.340 | 54.10 | 16.72 | 1.41 | 0.72 |
| MSZ10-350 | 38.82 | 2.19 | 0.350 | 55.69 | 17.22 | 1.45 | 0.74 |
| MSZ10-375 | 38.82 | 2.19 | 0.373 | 59.67 | 18.45 | 1.56 | 0.79 |
| MSZ10-406 | 38.82 | 2.19 | 0.406 | 64.60 | 19.97 | 1.73 | 0.86 |
| MSZ11-312 | 38.55 | 3.53 | 0.312 | 49.72 | 15.48 | 6.83 | 3.76 |
| MSZ11-340 | 38.55 | 3.53 | 0.340 | 54.1 | 16.84 | 7.43 | 4.06 |
| MSZ11-350 | 38.55 | 3.53 | 0.350 | 55.69 | 17.34 | 7.65 | 4.17 |
| MSZ11-375 | 38.55 | 3.53 | 0.375 | 59.67 | 18.58 | 8.21 | 4.44 |
| MSZ11-406 | 38.55 | 3.53 | 0.406 | 64.6 | 20.11 | 8.92 | 4.79 |
| MSZ12-312 | 37.72 | 6.64 | 0.312 | 49.72 | 8.76 | 29.29 | 8.76 |
| MSZ12-340 | 37.72 | 6.64 | 0.340 | 54.1 | 9.50 | 31.87 | 9.50 |
| MSZ12-350 | 37.72 | 6.64 | 0.350 | 55.69 | 9.77 | 32.84 | 9.77 |
| MSZ12-375 | 37.72 | 6.64 | 0.375 | 59.67 | 10.43 | 35.17 | 10.43 |
| MSZ12-406 | 37.72 | 6.64 | 0.406 | 64.6 | 11.27 | 38.16 | 11.27 |
| MSZ13-312 | 36.38 | 9.58 | 0.312 | 49.72 | 14.13 | 67.86 | 14.13 |
| MSZ13-340 | 36.38 | 9.58 | 0.340 | 54.10 | 15.32 | 73.79 | 15.32 |
| MSZ13-350 | 36.38 | 9.58 | 0.350 | 55.69 | 15.74 | 75.93 | 15.74 |
| MSZ13-375 | 36.38 | 9.58 | 0.375 | 50.67 | 16.81 | 81.34 | 16.81 |
| MSZ13-406 | 36.38 | 9.58 | 0.406 | 64.6 | 18.18 | 88.27 | 18.18 |
| MSZ14-312 | 34.56 | 12.24 | 0.312 | 12.27 | 19.62 | 120.97 | 19.62 |
| MSZ14-340 | 34.56 | 12.24 | 0.340 | 18.89 | 21.29 | 131.28 | 21.29 |
| MSZ14-350 | 34.56 | 12.24 | 0.350 | 19.34 | 21.91 | 135.50 | 21.91 |
| MSZ14-375 | 34.56 | 12.24 | 0.375 | 20.72 | 23.38 | 144.93 | 23.38 |
| MSZ14-406 | 34.56 | 12.24 | 0.406 | 22.43 | 25.29 | 157.25 | 25.29 |
| MSZ15-312 | 32.79 | 14.11 | 0.312 | 49.72 | 18.20 | 172.66 | 24.24 |
| MSZ15-340 | 32.79 | 14.11 | 0.340 | 54.10 | 19.80 | 187.52 | 26.27 |
| MSZ15-350 | 32.79 | 14.11 | 0.350 | 55.69 | 20.38 | 193.26 | 27.06 |
| MSZ15-375 | 32.79 | 14.11 | 0.375 | 59.67 | 21.84 | 207.03 | 28.91 |
| MSZ15-406 | 32.79 | 14.11 | 0.406 | 64.60 | 23.64 | 224.46 | 31.27 |
| MSZ16-312 | 31.05 | 15.54 | 0.312 | 49.72 | 19.22 | 223.36 | 28.45 |
| MSZ16-340 | 31.05 | 15.54 | 0.340 | 54.10 | 20.91 | 242.98 | 30.88 |
| MSZ16-350 | 31.05 | 15.54 | 0.350 | 55.69 | 21.53 | 249.85 | 31.74 |
| MSZ16-375 | 31.05 | 15.54 | 0.375 | 59.67 | 23.06 | 267.87 | 33.95 |
| MSZ16-406 | 31.05 | 15.54 | 0.406 | 64.60 | 24.97 | 290.74 | 36.75 |
| MSZ17-312 | 29.71 | 16.43 | 0.312 | 49.72 | 20.09 | 262.34 | 31.60 |
| MSZ17-340 | 29.71 | 16.43 | 0.340 | 54.1 | 21.86 | 285.10 | 34.27 |
| MSZ17-350 | 29.71 | 16.43 | 0.350 | 55.69 | 22.50 | 293.36 | 35.25 |
| MSZ17-575 | 29.71 | 16.43 | 0.375 | 59.67 | 24.11 | 314.57 | 37.71 |
| MSZ17-406 | 29.71 | 16.43 | 0.406 | 64.60 | 26.10 | 241.03 | 40.80 |
| MSZ18-312 | 28.38 | 17.2 | 0.312 | 49.73 | 20.58 | 296.05 | 34.49 |
| MSZ18-340 | 28.38 | 17.2 | 0.24 | 54.1 | 22.39 | 322.09 | 37.45 |
| MSZ18-350 | 28.38 | 17.2 | 0.350 | 55.69 | 23.04 | 330.95 | 38.46 |
| MSZ18-375 | 28.38 | 17.2 | 0.375 | 59.67 | 24.69 | 354.49 | 41.12 |
| MSZ18-406 | 28.38 | 17.2 | 0.406 | 64.6 | 26.74 | 384.83 | 44.53 |
| MSZ19-340 | 26.88 | 17.9 | 0.340 | 54.1 | 23.61 | 368.18 | 41.17 |
| MSZ19-350 | 26.88 | 17.9 | 0.350 | 55.69 | 24.30 | 867.04 | 42.24 |
| MSZ19-375 | 26.88 | 17.9 | 0.375 | 59.67 | 26.04 | 929.74 | 45.25 |
| MSZ19-406 | 26.88 | 17.9 | 0.406 | 64.60 | 28.19 | 1008.15 | 48.97 |